You will serve as a NONDESTRUCTIVE TEST INSPECTOR in the Industrial Processes Division of the MRO Production Department of FLTREADCEN EAST.

Duties

You will perform traditional nondestructive inspection of castings, forgings, machined parts, test plates, welds, metal cladding, pipes, bar stock, flat metal sheets, airframe and engine assemblies and nonmetallic materials. You will measure instruments and chemical applicable to the total range of nondestructive examination methods. You will calibrate and operate traditional test equipment such as ultrasonic testing (UT) equipment, eddy current testing (ET) equipment, magnetic particle testing (MT) equipment, and penetrant testing (PT) equipment. You will Inspect parts for flaws or defects, discontinuities in patterns, interprets indications and documents flaws or defects in material and prepares reports on defective parts. You will work with subordinate inspectors to set the pace and demonstrate proper inspection methods and may be required to work with trainees.

Requirements

• Must be a US Citizen.
• Must be determined suitable for federal employment.
• Must participate in the direct deposit pay program.
• New employees to the Department of the Navy will be required to successfully pass the E-Verify employment verification check. To learn more about E-Verify, including your rights and responsibilities, visit e-verify.gov
• Within the Department of Defense (DoD), the appointment of retired military members within 180 days immediately following retirement date to a civilian position is subject to the provisions of 5 United States Code 3326.
• Males born after 12-31-59 must be registered for Selective Service.
• You will be required to obtain and maintain an interim and/or final security clearance prior to entrance on duty. Failure to obtain and maintain the required level of clearance may result in the withdrawal of a job offer or removal.
• This position may require travel from normal duty station to CONUS and OCONUS and may include remote or isolated sites. You must be able to travel on military and commercial aircraft for extended periods of time.
• You will be required to successfully complete a pre-appointment physical examination.

Qualifications

Although a specific length of time and experience is not required for most trade and labor occupations, you must show through experience and training that you possess the quality level of knowledge and skill necessary to perform the duties of the position at the level for which you are applying. Qualification requirements emphasis is on quality of experience, not necessarily the length of time. Your qualifications will be evaluated on the basis of your level of knowledge, skills, abilities and/or competencies in the job elements and screen out listed below. This job has a screen-out element which will be used to determine minimum eligibility for this job. Applicants who do not receive a minimum of two points on the screen-out element(s) will be found ineligible. The Screen-out Element for this position is: 1) Calibrates and operates traditional test equipment such as ultrasonic testing (UT) Equipment. 3) Inspects parts for flaws or defects, discontinuities in patterns, interprets indications and documents flaws or defects in material and prepares reports on defective parts. 3) Works with subordinate inspectors to set the pace and demonstrate proper inspection methods and may be required to work with trainees. 4) Performs traditional nondestructive inspection of castings, forgings, machined parts, test plates, welds, metal cladding, pipes, bar stock, flat metal sheets, airframe and engine assemblies and nonmetallic materials (composites) 5) Reads and interprets specifications, sketches, blueprints, technical directives, manuals and shop orders to interpret and/or develop information on products to be tested and examined. Applicants must meet the requirements of the Office of Personnel Management (OPM) Job Qualification Handbook for Trades and Labor Occupations. Additional qualification information can be found at: https://www.opm.gov/policy-data-oversight/classification-qualifications/federal-wage-system-qualifications/#url=List-of-Approved-Job-Elements Experience refers to paid and unpaid experience, including volunteer work done through National Service programs (e.g., professional, philanthropic, religious, spiritual, community, student, social). Volunteer work helps build critical competencies, knowledge, and skills and can provide valuable training and experience that translates directly to paid employment.

Contacts

• Address FLTREADCEN EAST PSC 8021 Cherry Point, NC 28533-0021 US
• Name: Department of Navy EIC
• Email: [email protected]