Over 1 Million Paying Vacancies Available. Discover Your Dream Vacancy with Us!

Are you looking for a ELECTRONIC INDUSTRIAL CONTROLS MECHANIC? We suggest you consider a direct vacancy at United States Fleet Forces Command in Kittery. The page displays the terms, salary level, and employer contacts United States Fleet Forces Command person

Job opening: ELECTRONIC INDUSTRIAL CONTROLS MECHANIC

Salary: $28 - 33 per hour
City: Kittery
Published at: Aug 15 2022
Employment Type: Full-time
You will serve as a ELECTRONIC INDUSTRIAL CONTROLS MECHANIC in the CRANE MAINTENANCE DIVISION OF THE LIFITNG AND HANDLING DEPARTMENT of PORTSMOUTH NAVAL SHIPYARD.

Duties

You will troubleshoot, repair, calibrate, test and install industrial electronic controlled equipment. You will work on microprocessors, computers and associated peripheral equipment such as keyboards, as well as any other industrial transportation equipment with electronic controls or devices. You will perform diagnostic troubleshooting techniques to isolate faults using a wide variety of sophisticated test equipment such as digital voltmeters, oscilloscopes, signal generators, logic analyzers and line monitors. You will align and calibrate equipment using calibration standards and alignment procedures when available and occasionally aligns by using schematics and available technical data.

Requirements

  • Must be a US Citizen.
  • Must be determined suitable for federal employment.
  • Must participate in the direct deposit pay program.
  • New employees to the Department of the Navy will be required to successfully pass the E-Verify employment verification check. To learn more about E-Verify, including your rights and responsibilities, visit e-verify.gov
  • Within the Department of Defense (DoD), the appointment of retired military members within 180 days immediately following retirement date to a civilian position is subject to the provisions of 5 United States Code 3326.
  • Males born after 12-31-59 must be registered for Selective Service.
  • Per the preliminary nationwide injunction on E.O. 14043, COVID-19 vaccinations will not be implemented or enforced. For more information on vaccine status and workplace safety protocol requirements see Additional Information below.
  • This may be a bargaining unit position.
  • You may be required to successfully complete a pre-appointment physical examination.
  • You will be required to obtain and maintain an interim and/or final security clearance prior to entrance on duty. Failure to obtain and maintain the required level of clearance may result in the withdrawal of a job offer or removal.
  • This may be a Drug Testing position. If so, successful completion of a pre-employment drug test (including marijuana) is required.
  • A tentative offer of employment will be rescinded if you fail to report to the drug test appointment or pass the test. You will be subject to random drug testing.
  • You may be required to wear personal protective equipment such as helmets, gloves, coveralls, glasses, goggles, respirators and safety shoes continuously for the duration of the work shift.
  • Work may be performed in areas where potentially harmful physical and chemical agents are present (e.g. fumes, dust, heat, ionizing and non-ionizing radiation and chemicals). You may be required to participate in medical surveillance programs.
  • This position may require exposure to high noise levels.
  • This position may require travel from normal duty station to CONUS and OCONUS and may include remote or isolated sites. You must be able to travel on military and commercial aircraft for extended periods of time.
  • This position may be subject to work an uncommon tour, including nights, weekends, and holidays to meet mission requirements. Overtime or night differential pay and/or unusual duty hours may be required.

Qualifications

Although a specific length of time and experience is not required for most trade and labor occupations, you must show through experience and training that you possess the quality level of knowledge and skill necessary to perform the duties of the position at the level for which you are applying. Qualification requirements emphasis is on quality of experience, not necessarily the length of time. Your qualifications will be evaluated on the basis of your level of knowledge, skills, abilities and/or competencies in the job elements and screen out listed below. This job has a screen-out element which will be used to determine minimum eligibility for this job. Applicants who do not receive a minimum of two points on the screen-out element(s) will be found ineligible. The Screen-out Element for this position is: ABILITY TO DO THE WORK OF THE POSITION WITHOUT MORE THAN NORMAL SUPERVISION. Applicants must meet the requirements of the Office of Personnel Management (OPM) Job Qualification Handbook for Trades and Labor Occupations. Additional qualification information can be found at: https://www.opm.gov/policy-data-oversight/classification-qualifications/federal-wage-system-qualifications/#url=List-of-Approved-Job-Elements Experience refers to paid and unpaid experience, including volunteer work done through National Service programs (e.g., professional, philanthropic, religious, spiritual, community, student, social). Volunteer work helps build critical competencies, knowledge, and skills and can provide valuable training and experience that translates directly to paid employment.

Education

This job does not have an education qualification requirement.

Contacts

  • Address PORTSMOUTH NAVAL SHIPYARD HRO Building 44/1 Portsmouth, NH 03804-5000 US
  • Name: Department of Navy EIC
  • Email: [email protected]

Similar vacancies

PRODUCTION SHOP PLANNER (ELECTRONIC INDUSTRIAL CONTROL MECHANIC) May 29 2024
$40 - 47

You will compile work packages that accompany the Task Group Instructions (TGI's) / Technical Work Documents (TWJ)'s) through the duration of task execution. ...

ELECTRONIC INDUSTRIAL CONTROLS MECHANIC Mar 22 2024
$34 - 39

You will troubleshoot and repair all types of computer systems. You will perform calibration procedures to verify equipment working within required toleranc...

ELECTRONIC INDUSTRIAL CONTROLS MECHANIC Oct 04 2023
$32 - 37

You will troubleshoot, repair, calibrate, test and install industrial electronic controlled equipment. You will work on microprocessors, computers and asso...

ELECTRONIC INDUSTRIAL CONTROLS MECHANIC LEADER Aug 24 2023
$32 - 38

You will lead the work of electronic industrial controls mechanics and apprentices. You will resolve work related problems and take necessary corrective ac...

ELECTRONIC INDUSTRIAL CONTROLS MECHANIC Mar 22 2024
$29 - 34

You will perform work of limited skills which does not require the all-around skills of an electronic industrial controls mechanic journeyman. You will alig...