This is a public notice flyer to notify interested applicants of anticipated vacancies. Applications will not be accepted through this flyer. Interested applicants must follow the directions in the "How to Apply" section of this flyer to be considered. There may or may not be actual vacancies filled from this flyer. Notice of Result letters will not be sent to applicants who respond to this flyer.

Duties

You will interpret engineering drawings which combine electrical and electronic schematics, logic diagrams, and mechanical drawings to perform electronics control maintenance. You will analyze diagnostic test readings and operating conditions of electronically controlled industrial equipment to isolate system malfunctions. You will use electronic test devices and specialized test equipment to troubleshoot malfunctions in electronic control equipment and components.

Requirements

• Must be a US Citizen.
• Must be determined suitable for federal employment.
• Must participate in the direct deposit pay program.
• New employees to the Department of the Navy will be required to successfully pass the E-Verify employment verification check. To learn more about E-Verify, including your rights and responsibilities, visit e-verify.gov
• Within the Department of Defense (DoD), the appointment of retired military members within 180 days immediately following retirement date to a civilian position is subject to the provisions of 5 United States Code 3326.
• Males born after 12-31-59 must be registered for Selective Service.
• Per the preliminary nationwide injunction on E.O. 14043, COVID-19 vaccinations will not be implemented or enforced. For more information on vaccine status and workplace safety protocol requirements see Additional Information below.
• This is a bargaining unit position.
• You will be required to obtain and maintain a current valid United States driver’s license.
• You will be required to successfully complete a pre-appointment physical examination.
• You will be required to wear personal protective equipment such as helmets, gloves, coveralls, glasses, goggles, respirators and safety shoes continuously for the duration of the work shift.
• You will be required to obtain and maintain an interim and/or final security clearance prior to entrance on duty. Failure to obtain and maintain the required level of clearance may result in the withdrawal of a job offer or removal.
• You may be required to obtain Continuous Emissions Monitoring System (CEMS) certification from a State Environmental Agency if required by the State.
• You will be required to complete training, obtain, and maintain a government credit card for travel and travel-related purchases.
• May be assigned to any basic work week or shift hours, including alternating shifts.
• In the event of an emergency, you may be required to report to work during non-duty/ duty hours and during emergency situations; may be assigned duties other than those identified in the position description.

Qualifications

Although a specific length of time and experience is not required for most trade and labor occupations, you must show through experience and training that you possess the quality level of knowledge and skill necessary to perform the duties of the position at the level for which you are applying. Qualification requirements emphasis is on quality of experience, not necessarily the length of time. Your qualifications will be evaluated on the basis of your level of knowledge, skills, abilities and/or competencies in the job elements and screen out listed below. This job has a screen-out element which will be used to determine minimum eligibility for this job. Applicants who do not receive a minimum of two points on the screen-out element(s) will be found ineligible. The Screen-out Element for this position is: I have the ability to perform common tasks including 1) Work with high voltage equipment and systems ranging up to 34,500 volts; 2) Troubleshooting and repairing malfunctioning components associated with a general purpose digital computer control systems and electrical utility controls systems; 3) Read and interpret drawings, sketches, wiring diagrams and manufacturing specification and manuals; and 4) Use test equipment (oscilloscopes, voltmeters and ohmmeters and interface equipment to computer systems . I work under close supervision of a work leader or journey-level employee who observes tasks in progress and upon completion to make sure they are properly performed. Applicants must meet the requirements of the Office of Personnel Management (OPM) Job Qualification Handbook for Trades and Labor Occupations. Additional qualification information can be found at: https://www.opm.gov/policy-data-oversight/classification-qualifications/federal-wage-system-qualifications/#url=Overview Specialized experience statement: 1) Installs, overhauls, repairs, fabricates, and/or modifies electronically controlled industrial systems, components, and/or subassemblies. 2) Perfonns pretest, operational (functional), and final testing; final tuning; alignment; and/or calibration of highly complex electronic systems, components, and/or subassemblies. 3) Performs preventive maintenance on electronic industrial control systems to include disassembly, cleaning, reassembly, and calibration. 4) Utilizes safety and security practices and procedures following established rules and regulations and maintains a safe, clean, and secure work environment.

Education

N/A

Contacts

• Address NAVAL FAC ENGINEERING CMD WASH 1001 North St SE 208 Washington, DC 20020 US
• Name: Tocara Wells
• Phone: 202 975 8206
• Email: [email protected]