See below for important information regarding this job.

Duties

If filled at the WG-5 level, position has promotion potential to the positions of Electronic Industrial Controls Worker, WG-8; Electronic Industrial Controls Mechanic, WG-11; and the target position Electronic Industrial Controls Mechanic, WG-12. If selected at the WG-05, WG-08 or WG-11 level, the following duties will be performed in a developmental capacity. Performs preliminary inspection, overhaul/repair, retrofitting, modification and complete final operational testing and calibration of Industrial Plant Equipment (IPE) Diagnoses and localizes a problem to a specific, electronic, electrical, optical, hydraulic, pneumatic or mechanical malfunction. Localizes, isolates and repairs or replaces faulty electronic modules and components by using schematics, logic diagrams, logic symbology, technical instructions, logic testing equipment, manual data input, and computer stored program procedures. Performs testing, rewiring, repairing, overhauling, tracing and troubleshooting of electrical circuits, replacing of control units, electrical panels, fuses, and switches. Tests overall Computer Numerical Controlled (CNC) system operation by using data input in all modes to insure proper machine response and accuracy.

Requirements

• Must be a U.S. citizen
• Tour of Duty: 1st Shift
• Security Requirements: Non-Critical Sensitive with Secret Access
• Appointment is subject to the completion of a favorable suitability or fitness determination, where reciprocity cannot be applied; unfavorably adjudicated background checks will be grounds for removal.
• Fair Labor Standards Act (FLSA): Non-Exempt
• Selective Service Requirement: Males born after 12-31-59 must be registered or exempt from Selective Service.
• Recruitment Incentives: Not Authorized
• Bargaining Unit Status: Yes
• Pre-Employment Physical: Required

Qualifications

To qualify for an Electronic Industrial Controls Mechanic Helper / Electronic Industrial Controls Worker / Electronic Industrial Controls Mechanic, your resume and supporting documentation must support: Applicants will be rated in accordance with the Office of Personnel Management Qualification Standard for Trades and Labor Occupations. Although a specific length of time and experience is not required, you must meet any screen-out element listed, and show through experience and training that you possess the quality level of knowledge and skill necessary to perform the duties at the level for which you are applying. Emphasis is placed on how you gained the quality of experience, not necessarily the length of time, and that you have the required ability or potential to perform the job. Applicants who do not meet the screen-out element (SOE) will be eliminated from further competition. WG-05; Ability to do the work of an Electronic Industrial Controls Mechanic Helper/ Electronic Industrial Controls Mechanic without more than normal supervision; I perform the common tasks of the job to be filled but under close supervision, such as cleaning, disassembling, and reassembling components associated with Industrial Plant Equipment, building non-complex electrical panels consisting of contactors, fuse blocks, relays, transformers, and disconnects. Cutting, bending, threading conduit. Drilling and tapping holes in castings to mount electrical components. WG-08; Ability to do the work of an Electronic Industrial Controls Mechanic Helper/ Electronic Industrial Controls Mechanic without more than normal supervision; I perform the common tasks of the job to be filled but under close supervision, such as assisting in the maintenance of electrical/electronic components. Taking direction from higher-grade mechanic while overhauling, installing, maintaining and repairing a variety of electronically/electrically controlled industrial equipment. Following specific directions while troubleshooting various electronic/electrical systems. Working as a team member in the installation, repair, and maintenance of complete computer numerical control, or similar systems by performing more simple and routine tasks, such as identifying, checking three phase motor systems, programmable logic controllers, AC variable frequency drives, DC SCR drives and connecting power and signal cables, replacing defective parts and assemblies which have been identified by higher grade mechanics, or monitoring systems operation by following operating testing procedures for the system and associated test equipment, and identifying and reporting improper operation indications. WG-11; Ability to do the work of an Electronic Industrial Controls Mechanic Helper/ Electronic Industrial Controls Mechanic without more than normal supervision; I perform the common tasks of the job to be filled but under close supervision, such as such as preliminary inspection, overhaul/repair, retrofitting, modification and complete final operational testing and calibration of Industrial Plant Equipment (IPE) items. Demonstrates expert skill in diagnosing malfunctions by applying a high degree of knowledge of diverse occupational areas which include electronic, electrical, pneumatic, mechanical, repair/rebuild instrumentation and hydraulic trades. Requires a high degree of understanding of computer numerical control logic, closed loop servo systems, analog and digital DC SCR Drives, analog and digital AC Variable Frequency Drives, programmable logic controllers, discrete 1/0 devices, and computer generated electrical prints utilizing a CAD system. Uses, repairs and inspects electronic and position measuring equipment such as the laser interferometer, optical systems, position readouts and their associated components and circuits. Tests, repairs and troubleshoots electronic AC and DC SCR type drive systems, director servo amplifiers, checks critical voltages and switching devices to assure proper operation. Uses Laser equipment to perform and plot automatically actual linear displacement measurements and straightness, squareness and parallelism analysis. WG-12; Ability to do the work of an Electronic Industrial Controls Mechanic Helper/ Electronic Industrial Controls Mechanic without more than normal supervision; My experience is not reflected in the above statements. Experience refers to paid and unpaid experience, including volunteer work done through National Service programs (e.g., Peace Corps, AmeriCorps) and other organizations (e.g., professional, philanthropic, religious, spiritual, community, student, social). Volunteer work helps build critical competencies, knowledge, and skills and can provide valuable training and experience that translates directly to paid employment. You will receive credit for all qualifying experience, including volunteer experience.

Contacts

• Address DLA Aviation 6090 Strathmore Road Richmond, VA 23237 US
• Name: DLA Aviation POC
• Phone: 614-692-0318
• Email: [email protected]