Click on "Learn more about this agency" button below to view Eligibilities being considered and other IMPORTANT information. The primary purpose of this position is to develop, modify, and apply inspection procedures, techniques, and acceptability standards for new, unusual, and/or experimental nondestructive inspection processes using ultrasonic, eddy current and/or radiographic inspection techniques.

Duties

- Using the ultrasonic-eddy current processes, performs inspections of aircraft, engine, missile, ground support equipment, etc., parts and components, support equipment structural members, components, parts, and other materials for which inspection procedures and/or acceptability standards are inadequate or not available. - Using the radiographic equipment, performs inspections of aircraft, engine, missile, ground support equipment, etc., parts, components, support equipment structural members, components, parts, and other materials for which inspection procedures and/or acceptability standards are inadequate or not available. - Serves as NDI Technical Advisor, advising responsible shop supervisors, engineering, quality assurance and other related functions of defects found, their extent and their effect of the quality and serviceability of products. - Uses and maintains tools. - Utilizes safety practices and procedures following established safety rules and regulations to maintain a safe and clean work environment. - Maintains records and documents actions.

Requirements

• U.S. Citizenship Required
• Males must be registered for Selective Service, see www.sss.gov
• This posn is subject to provisions of the DoD Priority Placement Program
• Disclosure of Political Appointments
• May be required to work rotating shifts or uncommon tours of duty. Subject to call back to meet emergency situations.
• The physical requirements of this position as determined by the manager are: Prolonged standing, frequent lifting of parts and materials weighing up to 40 pounds unassisted, and occasionally over 50 pounds with assistance
• of lifting devices or other workers is required. Subject to eyestrain when using black light. Both hands and good eyesight required. Work requires stooping, bending, reaching, stretching, and climbing in, on, or through aircraft with equipment.
• Work requires employee to drive a motor vehicle. Valid driver’s license will be required.
• Must be certified IAW 33B-1-1 APPENDIX A field level requirements.
• This position has been designated by the Air Force as a Testing Designated Position (TDP) under the Air Force Civilian Drug Demand Reduction Program. Employee must pass initial and periodic short notice drug testing.
• Illegal drug use by employees in sensitive positions presents a clear threat to the mission of the Air Force, national security, and public safety.

Qualifications

In order to qualify, you must meet the quality level of experience requirements described in the Office of Personnel Management (OPM) Qualification Standards Handbook X-118C. QUALIFICATIONS: Applicants will be rated in accordance with the OPM Qualification Standard Handbook X-118C for the WG-3700 Metal Processing Group. Although a specific length of time and experience is not required for most blue-collar positions, you must meet any screen-out element listed and show through experience and training that you possess the quality level of knowledge and skill necessary to perform the duties of the position at the level for which you are applying. Qualification requirements emphasis is on the quality of experience, not necessarily the length of time. The screen out element for this position is ability to do the work of a NONDESTRUCTIVE TESTER without more than normal supervision. JOB ELEMENTS: Your qualifications will be evaluated on the basis of your level of knowledge, skills, abilities and/or competencies in the following areas: 1. Knowledge of ultrasonic-eddy current and industrial x-ray radiographic methods and equipment of nondestructive testing to investigate failures in critical aircraft structures and components when considerable unknown factors are involved; and various shapes, sizes, and density of flaw indications in parts being tested. 2. Knowledge of safety regulations and procedures. 3. Skill to set up and operate ultrasonic, eddy-current, and radiographic equipment to examine a variety of parts, components, or material to detect hidden subsurface flaws, corrosion, and separation in bonded and honeycomb structures; and determine integrity of welds, precision dimensional and volume measurements, hardness of materials, and if defects found, render the article acceptable or unacceptable. 4. Skill to work with quality assurance and engineering personnel to modify inspection procedures and test standards to achieve inspection objectives. 5. Ability to develop, modify, and adapt ultrasonic-eddy current, industrial x-ray radiographic methods and techniques of nondestructive testing to investigate failures in critical aircraft structures and components when existing inspection procedures, techniques, and acceptability standards are nonexistent or not applicable; and interpret flaw indications and their relevance to the reliability of products. 6. Ability to read and interpret quality control directives, engineering drawings, NDI literature, and technical orders concerning nondestructive testing methods and procedures; document actions; and maintain records manually or on a computer terminal. Physical Effort: Prolonged standing, frequent lifting of parts and materials weighing up to 40 pounds unassisted, and occasionally over 50 pounds with assistance of lifting devices or other workers is required. Subject to eyestrain when using black light. Both hands and good eyesight required. Work requires stooping, bending, reaching, stretching, and climbing in, on, or through aircraft with equipment. Working Conditions: Works inside shop and in areas adjacent to or removed from the shop. Exposed to oils, which may cause dermatitis or allergy. Subject to possible radiation damage of body tissues. Wears radiation monitoring devices, standard safety equipment, and protective clothing. PART-TIME OR UNPAID EXPERIENCE: Credit will be given for appropriate unpaid and or part-time work. You must clearly identify the duties and responsibilities in each position held and the total number of hours per week. VOLUNTEER WORK EXPERIENCE: Refers to paid and unpaid experience, including volunteer work done through National Service Programs (i.e., Peace Corps, AmeriCorps) and other organizations (e.g., professional; philanthropic; religious; spiritual; community; student and social). Volunteer work helps build critical competencies, knowledge and skills that can provide valuable training and experience that translates directly to paid employment. You will receive credit for all qualifying experience, including volunteer experience.

Education

This job does not have an education qualification requirement.

Contacts

• Address JBSA Randolph AFB 550 D Street East JBSA Randolph AFB, TX 78150 US
• Name: Total Force Service Center
• Phone: 1-800-525-0102
• Email: [email protected]