THIS IS A NATIONAL GUARD TITLE 32 EXCEPTED SERVICE POSITION. This National Guard position is for a ELECTRONIC MEASUREMENT EQUIPMENT MECHANIC, Position Description Number D1201000 and is part of the DE Combined Support Maintenance Shop, National Guard.

Duties

WG-2602-11: (1) Calibrates and repairs TMDE within support capability and authority including various levels of calibration as designated in technical bulletins, manuals, etc. Performs functional electronic, physical, and radioactive testing involving interpretation and analysis of measurement data, in accordance with cyclic inspection requirements. Aligns, troubleshoots, tests, inspects, repairs, modifies, calibrates and certifies precision measurement equipment such as multi-meters, microwave equipment, oscilloscopes, temperature analyzers, mercurial barometers, gage blocks and micrometer caliper dimensional equipment, digital voltmeters, signal generators, torque wrenches, pressure gauges, torque testers, weight scales, electronic counters, radiation monitors, radix calibrators, and radiation dosimeters. Analyzes and isolates component malfunctions; calculates and determines tolerances; and performs tests and calibrations in accordance with instructions, which are often vague and incomplete, and may require the preparation of diagrams and instructions to facilitate the calibration action. (2) Sets up system test sets and various types of test equipment such as frequency meters, standing wave ratio meters, radio frequency (RF) power meters, function/ arbitrary waveform generator, distortion analyzers, time frequency work stations, oscillators, voltmeters, electronic counters, oscilloscopes, attenuators, decade resistors and capacitors, signal generators, stroboscope, tachometers, pneumatic and hydraulic pressure standards and other physical and electronic tests. Diagnoses equipment, makes repairs, and replaces defective parts/components such as integrated circuits, printed circuit boards, electronic condition coils, radiation detector boards/circuits, crystals, transistors, tubes, transformers, condensers, diodes, relays potentiometers, and related components. (3) Following repair, tests by applying signals in known amplitude and wave shape into oscilloscopes to observe wave pattern. Isolates faults by taking measurements and comparisons in voltage, amperage, ohms, henries, power factor, watts, temperature, humidity, microns, foot-pounds, decibels, sensitivity, noise, stability, Voltage Standard Wave Ratio (VSWR), impedance, phase, absolute pressure, time intervals, displacement, flow rate, etc., to determine performance of equipment. If signal is distorted, traces it through electronic stages to locate malfunctioning part. Checks sweep rate by feeding known signal to an oscilloscope and observing wave pattern to correct shape and size. Operates equipment to complete range checking for proper operation of positioning controls. (4) Determines purpose in operation characteristics of each major section. Refers to technical manuals and manufactures specifications to obtain information on operation characteristics of circuit components such as integrated circuits, microprocessors, decoders, latching networks, notch filters, logics, controllers, programmable gain amplifiers, digital displays, transistors, tubes, transformers, coils, relays, motors, and similar devices. Disassembles, cleans and inspects parts such as printed circuit boards, resistors, capacitors, integrated circuits, relays, chambers, cables, and wiring for evidence or wear or malfunction. Repairs and/or replaces parts as required. Uses special test devices and radioactive samples or other calibrated sources. Tests equipment for sensitivity and correct operation. (5) Completes necessary Army Maintenance Management System (TAMMS), calibration, radiation reports and other records and forms on work completed. Ensures maximum number of weapons systems are operationally ready. Uses TMDE Integrated Maintenance Management Systems (TIMMS) for all supported equipment to track, turn-in, repair, calibrate, and return to the end user in a timely fashion to prevent work stoppages. Furnishes technical data to the supervisor for inclusion in reports as well as recommending equipment improvement and solutions for unusual problems related to testing and the use of precision TMDE. (6) Follows appropriate safety procedures, with special care being exercised while calibrating high voltage, radio frequency, radioactive sources and high-pressure instruments and gages. Performs and interprets wipe tests on radiation sources for possibility of radiation hazards. Familiar with and abides by all Federal and State regulations concerning handling, transportation and disposal of radioactive waste or devices. (7) Performs other duties as assigned.

Requirements

• NATIONAL GUARD MEMBERSHIP IS REQUIRED. If you are not sure you are eligible for military membership, please contact a National Guard recruiter prior to applying for this position.
• This is an excepted service position that requires membership in a compatible military assignment in the employing state's National Guard, required prior to the effective date of placement.
• Selectee will be required to wear the military uniform.
• Acceptance of an excepted service position constitutes concurrence with these requirements as a condition of employment.
• Applicants who are not currently a member of the National Guard must be eligible for immediate membership and employment in the National Guard in the military grade listed in this announcement.
• Males born after 31 December 1959 must be registered for Selective Service.
• Federal employment suitability as determined by a background investigation.
• May be required to successfully complete a probationary period.
• Participation in direct deposit is mandatory.
• Must meet the definition of specialized experience by the closing date of the position advertisement.
• Must have a minimum of 18 months of specialized experience to qualify at the WG-11

Qualifications

Military Grades: E-4/SPC - E-9/SGM, W01 - CW04 SPECIALIZED EXPERIENCE: Experience or training with basic application of operating principles such as the production and utilization of oscillations over a broad range of frequencies; signal and waveform behavior, distortion, and amplification; pulse, trigger, and synchronization techniques; digital/analog processing and data conversion techniques; and a variety of display and indication methods. Experience in tracing signals and voltage paths, and skilled in the analysis of waveform characteristics such as timing, duration, frequency, and phasing. Originates test set-ups to isolate malfunctions and check performance characteristics of special or unique test panels or mockups. Experience in interpreting and applying a variety of technical electronic information such as schematic symbols, mathematical expressions and formulas, calibration procedures, and other reference materials. Experience in applying established techniques and methods of repair, testing, alignment, and calibration of equipment, which serves as test equipment or precision measurement standards. Experience in utilizing electronic circuits to measure electronic or electrical quantities to determine the performance characteristics and accuracy of other instruments and equipment. Definition of Specialized Experience: **Specialized experience must be closely related to the work to be performed in the job for which you are applying and meet education, and other qualifications listed in the job announcement** QUALITY OF EXPERIENCE: Length of time is not of itself qualifying. Candidates' experience should be evaluated on the basis of duties performed rather than strictly on the rank of the individual; however, established compatibility criteria/assignments must be followed. The applicant's record of experience and/or training must show possession of the knowledge, skills and abilities needed to fully perform the duties of the position.

Education

There is no substitution of education for this position.

Contacts

• Address DE Combined Support Maintenance Shop 1197 River Road New Castle, DE 19720 US
• Name: Saidi Abdallah
• Phone: 302-326-7807
• Email: [email protected]