You will serve as an PLANNER AND ESTIMATOR (A/C SHEET METAL MECHANIC), in the MRO PRODUCTION DEPT, PRODUCTION LINES DIV FLEET READINESS CENTER SOUTHWEST.

Duties

You will develop, implement and coordinate aircraft sheet metal repair workload plans, program schedules and configuration control of the aircraft reworked, repaired, modified or converted. You will review established procedures and recommends improved methods to reduce aircraft rework costs and out of service time. You will explain the more technical aspects of the work and may instruct, demonstrate or help with especially difficult or unusual tasks. You will review timeliness and status of work being accomplished to balance workloads and resources among work units and meet established deadlines. You will observe work in progress to assure on time completion and verifies the quality going into the product and inspects work to ensure that standards for quality and quantity are met. You will prepare command correspondence, production and status reports for higher management and other commands and activities.

Requirements

• Must be a US Citizen.
• Must be determined suitable for federal employment.
• Must participate in the direct deposit pay program.
• New employees to the Department of the Navy will be required to successfully pass the E-Verify employment verification check. To learn more about E-Verify, including your rights and responsibilities, visit e-verify.gov
• Within the Department of Defense (DoD), the appointment of retired military members within 180 days immediately following retirement date to a civilian position is subject to the provisions of 5 United States Code 3326.
• Males born after 12-31-59 must be registered for Selective Service.
• You will be required to obtain and maintain an interim and/or final security clearance prior to entrance on duty. Failure to obtain and maintain the required level of clearance may result in the withdrawal of a job offer or removal.
• Must obtain and maintain all required certification and/or license as a condition of employment
• You may be required to wear personal protective equipment such as helmets, gloves, coveralls, glasses, goggles, respirators and safety shoes continuously for the duration of the work shift.
• You will be required to complete training, obtain, and maintain a government credit card for travel and travel-related purchases.
• You will be required to obtain and maintain a U.S. Passport.

Qualifications

Although a specific length of time and experience is not required for most trade and labor occupations, you must show through experience and training that you possess the quality level of knowledge and skill necessary to perform the duties of the position at the level for which you are applying. Qualification requirements emphasis is on quality of experience, not necessarily the length of time. Your qualifications will be evaluated on the basis of your level of knowledge, skills, abilities and/or competencies in the job elements and screen out listed below. This job has a screen-out element which will be used to determine minimum eligibility for this job. Applicants who do not receive a minimum of two points on the screen-out element(s) will be found ineligible. The Screen-out Element for this position is: ABILITY TO LEAD OR SUPERVISE I have the ability to independently perform the most difficult and complex tasks as an expert or have been consulted by other employees in difficult situations performing duties including: Have depot level experience working with MV22 Aircraft Planned Maintenace Interval Programs (PMI) MV22. CH53, C130 ISR Depot level repairs. Extensive knowledge in Leading and evaluating all ISR aircraft and understand PMI specifications and instructions. Works at offsite stations on MV22, CH53, C130 and other TMS when required as a structural sheet metal evaluator. Extensive understanding of the sheet metal trade and all tools/equipment required to perform such functions. I am considered an expert and work with a high degree of independence. I have the ability to perform the full range of tasks on my own initiative including: Have depot level experience working with MV22 Aircraft Planned Maintenace Interval Programs (PMI) MV22. CH53, C130 ISR Depot level repairs. Have knowledge in Leading and evaluating all ISR aircraft and understand PMI specifications and instructions. Prepared to work at offsite stations on MV22, CH53, C130 and other TMS when required as a structural sheet metal evaluator. Extensive understanding of the sheet metal trade and all tools/equipment required to perform such functions. I work on my own initiative under general observation or supervision subject to occasional inspection. I have the ability to perform common tasks under general observation or supervision including: Have depot level experience working with MV22 Aircraft Planned Maintenace Interval Programs (PMI) MV22. CH53, C130 ISR Depot level repairs. Knowledgeable in evaluating ISR aircraft and understand PMI specifications and instructions. Can work at offsite stations on MV22, CH53, C130 and other TMS when required as a structural sheet metal evaluator. Have an understanding of the sheet metal trade and all tools/equipment required to perform such functions. I work under the supervision of a higher level employee who observes tasks in progress and upon completion to make sure they are properly performed. I have the ability to perform simple tasks or I have received training on this type of work. I do not have on-the-job training or the abilities described above. Applicants must meet the requirements of the Office of Personnel Management (OPM) Job Qualification Handbook for Trades and Labor Occupations. Additional qualification information can be found at: https://www.opm.gov/policy-data-oversight/classification-qualifications/federal-wage-system-qualifications/#url=List-of-Approved-Job-Elements Experience refers to paid and unpaid experience, including volunteer work done through National Service programs (e.g., professional, philanthropic, religious, spiritual, community, student, social). Volunteer work helps build critical competencies, knowledge, and skills and can provide valuable training and experience that translates directly to paid employment.

Contacts

• Address FLEET READINESS CENTER SOUTHWEST Fleet Readiness Center Southwest PO Box 347058 San Diego, CA 92135-7058 US
• Name: Department of Navy EIC
• Email: [email protected]