THIS IS A NATIONAL GUARD TITLE 32 EXCEPTED SERVICE POSITION. This position is for a Tools and Parts Attendant, Position Description Number D1228000 located at FMS Clay, Marietta, Georgia. This is a full-time, Excepted Permanent, dual status position which requires Georgia Army National Guard Membership. Area of Consideration: Current onboard T32 Excepted Service technicians within the State of Georgia.

Duties

As a Tools and Parts Attendant, WG-6904-06, you will: Identify user's tools, parts, equipment, and requirements and requisitions stock as needed. Watch and report items that are in short supply because of breakage or because they are frequently out for repair. Recommend possible substitute or interchangeable items. Set up and maintain storage locations. Determine methods of storage, identification, and stock location, considering such factors as temperature, humidity, height and weight limits, turnover, floor loading capacities, space available, and convenience of handling items. Compile records concerned with quantity, cost, and type of material received, stored, and issued. Prepare periodic inventory and determine the basis for over, short, or misplaced items by checking such references as out-for-repair, issue, and turn-in records maintained in the tools and parts room. Compile reports of use of stock handling equipment, adjustments of inventory counts and stock records, spoilage of or damage to stock, location changes, and refusal of shipments. Ensure that tools and equipment are maintained in good condition by performing visual and operating checks, taking measurements with such devices as calipers, and receiving reports from users on the nature and extent of damage to tools and equipment. May make minor repairs to tools and equipment, determine when damaged and inoperative items are too costly to repair, and report damaged or worn-out equipment to superiors. Determine stock replenishment levels for centrally controlled supplies and other material within funding limitations. Assure that supplies and monies are not wasted through excess accumulation, and that items are on hand in sufficient quantities and at the time required. In addition to established guides and formulas, determines quantities required and timely stock replenishment. Receive a wide variety of supplies and specialized items requiring special handling. Ensure that received items are properly stored in assigned locations. Review requisitions for completeness and compliance with regulations, and revise quantities ordered based on number on hand. Recommend substitution when supply items are not available. Search for identifying or management data on items of supply. Compare data listed on documents with reference sources such as federal catalogs, stock lists, or other publications. Receive requests desiring additional identification data, verification, or comparison of data on hand with reference sources. Search for stock number, prices, descriptions, sources of supply, or other management data. When unknown, traces part number or type number and manufacturer of the item of equipment. Edit supply transactions, or provide customer service for urgent critical shortage items and other items requiring special handling when established procedures are not applicable. Code and classify requisitions, shipping orders, and other documents, and extracts requests to other sources of supply or refer them to an inventory control point when stock is unavailable or cannot be shipped. May assist a Surface Maintenance Mechanic by performing the less complex and more routine helper type duties. May perform maintenance tasks with repairers or mechanics by assisting in the accomplishment of duties. This may involve getting tools and supplies, carrying materials, and lifting and holding materials in place during operations. As directed by the repairer or mechanic, use hand and powered tools of the trade to assist in the disassembly, assembly, and installation of simple component parts and units. Apply knowledge gained from previous work assignments. Detailed instructions are received from the higher graded Surface Maintenance Mechanic with each new assignment. Work is reviewed by the higher-level employee while in progress and upon completion. Clean tools, parts, and equipment and keep work areas clean and orderly. Perform other duties as assigned.

Requirements

• NATIONAL GUARD MEMBERSHIP IS REQUIRED
• This is an excepted service position that requires membership in a compatible military assignment in the employing state's National Guard, required prior to the effective date of placement.
• Selectee will be required to wear the military uniform.
• Acceptance of an excepted service position constitutes concurrence with these requirements as a condition of employment.
• Males born after 31 December 1959 must be registered for Selective Service.
• Federal employment suitability as determined by a background investigation.
• May be required to successfully complete a probationary period.
• Participation in direct deposit is mandatory.
• For positions requiring the operation of motor vehicles, candidates must have a valid state drivers license.
• Preplacement Medical Requirements: Selectee will be required to undergo medical testing, at the expense of the government, prior to beginning employment. Medical tests are used to determine fitness and eligibility for employment.
• Must be able to obtain and maintain the appropriate security clearance of the position.
• This position is covered by the Domestic Violence Misdemeanor Amendment (30 Sep 96) of the Gun Control Act (Lautenberg Amendment) of 1968. An individual convicted of a qualifying crime of domestic violence may not perform the duties of this position.
• Ability to establish effective professional working relationships with coworkers and customers, contributing to a cooperative working environment and successful accomplishment of the mission.
• Irregular and/or overtime (compensatory) hours may be required to support operational requirements or contingencies or may be required to work hours outside of the normal duty day.
• Must be able to pass an operator's test for forklift equipment up to 10,000 lbs.

Qualifications

Each applicant must fully substantiate (in her/his own words) that they meet the requirements of the specialized experience listed below; otherwise, the applicant will be considered unqualified for this vacancy. DO NOT COPY THE VACANCY ANNOUNCEMENT OR THE POSITION DESCRIPTION. IF YOU DO THIS YOU WILL BE CONSIDERED UNQUALIFIED FOR THE VACANCY. Please ensure that you have included beginning and ending dates (month and year) for all jobs listed on your resume. Military Grades: Enlisted Compatible Military Assignments: ECMF: 12, 13, 14, 19, 25, 88, 91, 92, 94 EMOS: 92A, 92F, 92Y, 92Z General Experience: Must possess experience which demonstrates the knowledge of trade; ability to apply identification skill (matching specific item name, models, and stock or part numbers with similar specific information at stock locations); ability to use simple hand tools (pliers, screwdrivers, etc) and to follow oral and written instructions. Specialized Experience: Candidate must have specialized experience in verifying stock by opening, counting and visually checking the contents of the containers. Experience in establishing stock location by considering such factors as use, size, shape and weight of items. Experience in completing stock records by showing the names, quantities and location of stock. Experience in identifying correct nomenclature and stock number of items in order to locate stock for issue. Experience in performing maintenance such as replacing wooden handles on handsaws, changing blades on power saws, and greasing or oiling power and hand tools. Physical Effort: Work is performed on hard surfaces and in work areas that require standing, stooping, bending, and working in tiring and uncomfortable positions. Frequently lifts and carries tools, parts, supplies, and equipment weighing up to10 pounds. May occasionally handle items that weigh up to 40 pounds. Hand trucks, dollies, and other workers are available for assistance with heavier items. Working Conditions: Work is generally performed in areas that are well lighted, heated, and ventilated. May occasionally work inside in areas that are drafty. Work is sometimes dirty, dusty, and greasy. Frequently exposed to the possibility of cuts, scrapes, and bruises.

Contacts

• Address GA FMS CLAY 1000 Halsey Ave Bldg 38 Marietta, GA 30060 US
• Name: Olivia Green
• Phone: 678-569-5251
• Email: [email protected]