Job opening: ELECTRONIC MEASUREMENT EQUIPMENT MECHANIC
Salary: $33 - 41 per hour
Published at: Aug 16 2023
Employment Type: Full-time
THIS IS A NATIONAL GUARD TITLE 32 EXCEPTED SERVICE POSITION.
This position is located in the Joint Forces Headquarters-State, Logistics Directorate (J-4), Surface Maintenance Facility.
DEFINITION OF AREA(S) OF CONSIDERATION:
Area 1 = Warrant Officer (CW3 - Below) and Enlisted members of the Louisiana National Guard.
Duties
Duties & Responsibilities:
(1) Calibrates and repairs TMDE within support capability and authority including various levels of calibration as designated in technical bulletins, manuals, etc. Performs functional electronic, physical, and radioactive testing involving interpretation and analysis of measurement data, in accordance with cyclic inspection requirements. Aligns, troubleshoots, tests, inspects, repairs, modifies, calibrates and certifies precision measurement equipment such as multimeters, microwave equipment, oscilloscopes, temperature analyzers, mercurial barometers, gage blocks and micrometer caliper dimensional equipment, digital voltmeters, signal generators, torque wrenches, pressure gauges, torque testers, weight scales, electronic counters, radiation monitors, radix calibrators, and radiation dosimeters. Analyzes and isolates component malfunctions; calculates and determines tolerances; and performs tests and calibrations in accordance with instructions, which are often vague and incomplete, and may require the preparation of diagrams and instructions to facilitate the calibration action.
(2) Sets up system test sets and various types of test equipment such as frequency meters, standing wave ratio meters, radio frequency (RF) power meters, function/ arbitrary waveform generator, distortion analyzers, time frequency work stations, oscillators, voltmeters, electronic counters, oscilloscopes, attenuators, decade resistors and capacitors, signal generators, stroboscope, tachometers, pneumatic and hydraulic pressure standards and other physical and electronic tests. Diagnoses equipment, makes repairs, and replaces defective parts/components such as integrated circuits, printed circuit boards, electronic condition coils, radiation detector boards/circuits, crystals, transistors, tubes, transformers, condensers, diodes, relays potentiometers, and related components.
(3) Following repair, tests by applying signals in known amplitude and wave shape into oscilloscopes to observe wave pattern. Isolates faults by taking measurements and comparisons in voltage, amperage, ohms, henries, power factor, watts, temperature, humidity, microns, foot-pounds, decibels, sensitivity, noise, stability, Voltage Standard Wave Ratio (VSWR), impedance, phase, absolute pressure, time intervals, displacement, flow rate, etc., to determine performance of equipment. If signal is distorted, traces it through electronic stages to locate malfunctioning part. Checks sweep rate by feeding known signal to an oscilloscope and observing wave pattern to correct shape and size. Operates equipment to complete range checking for proper operation of positioning controls.
(4) Determines purpose in operation characteristics of each major section. Refers to technical manuals and manufactures specifications to obtain information on operation characteristics of circuit components such as integrated circuits, microprocessors, decoders, latching networks, notch filters, logics, controllers, programmable gain amplifiers, digital displays, transistors, tubes, transformers, coils, relays, motors, and similar devices. Disassembles, cleans and inspects parts such as printed circuit boards, resistors, capacitors, integrated circuits, relays, chambers, cables, and wiring for evidence or wear or malfunction. Repairs and/or replaces parts as required. Uses special test devices and radioactive samples or other calibrated sources.
(5) Completes necessary Army Maintenance Management System (TAMMS), calibration, radiation reports and other records and forms on work completed. Ensures maximum number of weapons systems are operationally ready. Uses TMDE Integrated Maintenance Management Systems (TIMMS) for all supported equipment to track, turn-in, repair, calibrate, and return to the end user in a timely fashion to prevent work stoppages. Furnishes technical data to the supervisor for inclusion in reports as well as recommending equipment improvement and solutions for unusual problems related to testing and the use of precision TMDE.
(6) Follows appropriate safety procedures, with special care being exercised while calibrating high voltage, radio frequency, radioactive sources and high-pressure instruments and gages. Performs and interprets wipe tests on radiation sources for possibility of radiation hazards. Familiar with and abides by all Federal and State regulations concerning handling, transportation and disposal of radioactive waste or devices.
(7) Performs other duties as assigned.
Qualifications
GENERAL EXPERIENCE: Must possess experience or training that has provided the candidate with a basic knowledge of machining processes; have the ability to use drill presses, shapers, planers and other types of associated machine tools.
SPECIALIZED EXPERIENCE: Must possess at least Eighteen (18) months experience or training performing the full range of machining operations on most types of conventional or CNC machine tools and their various attachments; experience or training in planning and lay out work from blueprints, worksheets and other drawings that may have missing or incorrect information; skill in applying shop mathematics in establishing needed dimensions, such as those required for chasing threads or machining angular surfaces; locating and marking surfaces and angles to be machined; skill in programming machining operations, setting up and operating CNC machine tools; knowledge of and ability to apply advanced shop mathematics such as geometric and trigonometric formulas to make computation for laying out work, machining pieces at unusual or compound angles, determining gear ratios pitch, angles and other similar exact or precision dimension.
Education
You must provide transcripts and/or other documentation as proof to support your Educational claims, and receive credit to meet the Education requirements for this position.
Contacts
- Address LA ARNG CONSOLIDATED SERVICES AND MAINTENANCE SHOP
119 WEST RANGE ROAD
PINEVILLE, LA 71360
US
- Name: LANG HRO INBOX
- Phone: 504-278-8600
- Email: [email protected]
Map